How To Remove Jalousie Windows

Jalousie windows are louvered windows. They, along with canopy style windows, are the ii most mutual styles of windows institute on vintage trailers. Jalousies (pronounced with the accent on the first syllable) were made by a number of different companies and used across almost brands of trailers starting in the mid-50s. Hehr and Phillips were the ii major brands. The Hehr 1600 series is the earliest and nearly prevalent.

After half a century or more, yous may notice you lot demand to do some maintenance to the aluminum drinking glass holders on the ends of each slat.  The glass holders vary based on the brand and model of window.  Here we describe how to remove the drinking glass holders from a Hehr 1600 window. Structure is similar on other models, although parts may look different.

The start pace in working with jalousie windows is to remove the glass and set it aside safely. This commonly does not require tools, other than perchance gently prying the end of the clip open only enough to remove the rubber pad (these can be replaced with new UV-proof silicone pads after).

Next, undo and remove the window crank operator. Our clutch caput $.25, item VTS-578, may greatly assist with this step.

With glass slats and operator removed, yous can see that each aluminum glass holder has two rivets. One is fastened equally the stock-still pivot signal to the window frame, and the other is fastened to a long apartment vertical link bar that moves up and down along the window's side to keep all the drinking glass slats operating simultaneously and in parallel.

The next stride volition be to remove the drinking glass holders from the window as a group. In other words, if you have 5 slats, all v glass holders on one side will come out together. You won't divide them from the long flat link. Yous'll disassemble them from the window frame.

Wait at the motion picture below: the five rusty rivets along the outside window frame must be drilled out. Using a ⅛" drill flake, drill just enough to sever the rolled end of the rivet and push the rest of the rivet through. This is the best fashion to prevent damage to the window frame.

The rivets are steel and so they rust and cause corrosion issues for the adjacent aluminum. Aluminum rivets were typically not used because these rivets are required to motion and aluminum would wear as well quickly. We highly recommend replacing these rivets with stainless steel rivets.

The type of rivet used is a specialized i chosen a semi-tubular rivet. Semi-tubular rivets are a one-piece solid rivet rather than a more than common popular rivet. The rivets have a solid slightly domed truss head on one side and a hollow tail that is squeezed or hammered using a dice that neatly finishes the back end by curling it outward. Installing a tubular rivet requires a few specialized tools and a specification of both the diameter and the precise length of riveted needed.

We recommend drilling out the old steel rivets from the tail terminate if possible. The tail offers an indentation to center your drill scrap. If you need to go from the caput side, just exist sure to use a split point drill bit and be very careful not to oval the hole. Remember, the new rivet needs to pivot in that pigsty.

With the long link and the glass holders released as a grouping from the window frame, you can move to a bench for the rest of the job.  Here you tin finish removing rivets then you can clean, straighten or supplant the glass holders.

When finished, everything goes back together in opposite order.

Tubular rivets and tools recommeneded for this chore:

• tubular rivets
• squeeze tool
• dies
• manus clincher
• clutch head $.25

While you are at it, nosotros suggest examining and/or replacing these items:

• Jalousie Glass Servant Discs, item VTS-171
• Jalousie Glass Holders, item VTS-389
• Jalousie Window Meridian and Bottom Seal, item VTS-239
• Pile Weatherstrip for Jalousie Windows, item VTS-333

Source: https://www.vintagetrailersupply.com/blog/replacing-jalousie-window-glass-holders/

Posted by: aycockdiestlyped.blogspot.com

Share this post